The Prop Lord
Well-Known Member
While this is an Unlimited Run, the only thing that limits amount, is material accessibility. Mainly due to the Leather supplier.
This Infinity Gauntlet is also articulating with a wide range of wrist and finger movement. How does that work? Genuine, Italian Lambskin Leather. The model, was scratch built, by me, 3d printed, and mastered to perfection.
Display video!
This version of the Infinity Gauntlet is based off of the movie, Infinity War. It is NOT a replica of the Display version you've seen floating around. The movie version is very different. And oh so much cooler!
________________________________________________________________
Breakdown:
-The glove portion, as previously stated, is Genuine, Italian Lambskin Leather. That's just fancy for, "it's more expensive than it should be and is hard to work with!" But man, is it soft! The inner section between the finger joints is fortified with different glues and dusted with mica powder to match the glove. This way, it's harder for the seams to split over time. The thumb section is carefully hand-machine embroidered with red thread. No embroidery machine is used!
-The hard parts are made from Cast Resin (Plastic). Each mold is coated with Bronze Mica powder. That's where 99% of that metallic shine comes from. So it's never going to rub off. That other "1%" is from Gold Spray Paint that is brushed over the entire gauntlet, 1 piece at a time before assembly. This gives the gauntlet an "Otherworldly" iridescence. Especially in the sunlight. The hard parts are either glued with Contact Cement. Or Freesole rubber glue. Either seem to work just fine.
-Each Infinity Stone is unique. Each having it's own Crystalline structure. Just like in the movie. No stone is the same. Each stone has their own LED. In that video, the room is fully lit, and the "FLASH" mode is being used. Yet, the stones still glow quite brightly. It is powered by a simple 9 volt battery. No Cosmic Radiation poisoning! The best part? Your hand (except for when you first put the Gauntlet on) never touches the wires. All of the wires (but the battery wire) are underneath the armor plating.
The thumb and fingers have almost completely free movement. You can also rock your wrist in every direction because the armor plating "floats".
The price. How can you justify it? Well. Each of the 32 hard pieces are made individually from their own molds. Which takes, hours. The main arm piece alone takes a minimum of 4 hours of constant Roto-Casting (a non-stop process!). And boy, is it messy! Believe it or not, working with the leather is the hardest part. It's soft, but delicate if you're not careful when you sew it together. The LED portion is carefully, and correctly, soldered together and then encase in glue or resin so they can't come apart. The wires are carefully placed under the armor plating and glued down.
_________________________________________________________
Size and weight:
It's pretty huge. It's not made for baby hands. However, if you are Thanos sized. The fingers can potentially be a bit tight. It can easily fit a 6'2" man. If you need wider fingers, I can definitely do that for you! The first one I made fit a 6'11" man, like a glove! But I felt it was too loose for the average non-giant person.
From end to end it maxes out at roughly 19 inches long.
It's not heavy. But it isn't "light". It is cast quite thick so you can drop it (accidentally!) and it won't break on you. We've tried.
_________________________________________________________
At the time of taking these pics, there were a few air bubbles. Which have been filled back with resin. The one pictured is still available, and ready to go.
Pricing and Payment:
PayPal (Goods and Services) OR Etsy.
$350 + Shipping
$15 in USA (USPS Priority)
$30 outside USA. (USPS International)
Infinity Gauntlet Replica (Articulating and Screen Accurate)
_________________________________________________________
Spots depend on leather on hand:
1.
2.
3.
4.
Run ended
This Infinity Gauntlet is also articulating with a wide range of wrist and finger movement. How does that work? Genuine, Italian Lambskin Leather. The model, was scratch built, by me, 3d printed, and mastered to perfection.
Display video!
This version of the Infinity Gauntlet is based off of the movie, Infinity War. It is NOT a replica of the Display version you've seen floating around. The movie version is very different. And oh so much cooler!
________________________________________________________________
Breakdown:
-The glove portion, as previously stated, is Genuine, Italian Lambskin Leather. That's just fancy for, "it's more expensive than it should be and is hard to work with!" But man, is it soft! The inner section between the finger joints is fortified with different glues and dusted with mica powder to match the glove. This way, it's harder for the seams to split over time. The thumb section is carefully hand-machine embroidered with red thread. No embroidery machine is used!
-The hard parts are made from Cast Resin (Plastic). Each mold is coated with Bronze Mica powder. That's where 99% of that metallic shine comes from. So it's never going to rub off. That other "1%" is from Gold Spray Paint that is brushed over the entire gauntlet, 1 piece at a time before assembly. This gives the gauntlet an "Otherworldly" iridescence. Especially in the sunlight. The hard parts are either glued with Contact Cement. Or Freesole rubber glue. Either seem to work just fine.
-Each Infinity Stone is unique. Each having it's own Crystalline structure. Just like in the movie. No stone is the same. Each stone has their own LED. In that video, the room is fully lit, and the "FLASH" mode is being used. Yet, the stones still glow quite brightly. It is powered by a simple 9 volt battery. No Cosmic Radiation poisoning! The best part? Your hand (except for when you first put the Gauntlet on) never touches the wires. All of the wires (but the battery wire) are underneath the armor plating.
The thumb and fingers have almost completely free movement. You can also rock your wrist in every direction because the armor plating "floats".
The price. How can you justify it? Well. Each of the 32 hard pieces are made individually from their own molds. Which takes, hours. The main arm piece alone takes a minimum of 4 hours of constant Roto-Casting (a non-stop process!). And boy, is it messy! Believe it or not, working with the leather is the hardest part. It's soft, but delicate if you're not careful when you sew it together. The LED portion is carefully, and correctly, soldered together and then encase in glue or resin so they can't come apart. The wires are carefully placed under the armor plating and glued down.
_________________________________________________________
Size and weight:
It's pretty huge. It's not made for baby hands. However, if you are Thanos sized. The fingers can potentially be a bit tight. It can easily fit a 6'2" man. If you need wider fingers, I can definitely do that for you! The first one I made fit a 6'11" man, like a glove! But I felt it was too loose for the average non-giant person.
From end to end it maxes out at roughly 19 inches long.
It's not heavy. But it isn't "light". It is cast quite thick so you can drop it (accidentally!) and it won't break on you. We've tried.
_________________________________________________________
At the time of taking these pics, there were a few air bubbles. Which have been filled back with resin. The one pictured is still available, and ready to go.
Pricing and Payment:
PayPal (Goods and Services) OR Etsy.
$350 + Shipping
$15 in USA (USPS Priority)
$30 outside USA. (USPS International)
Infinity Gauntlet Replica (Articulating and Screen Accurate)
_________________________________________________________
Spots depend on leather on hand:
1.
2.
3.
4.
Run ended
Last edited:
