Interest Clan Saber Craft #2: Shaak Ti - Barriss Offee

[guabe]

Next on the CSC system is the Shaak Ti / Barriss Offee hilts. Being part of this system means that the threading is compatible with the first project LINK

Main difference between the Shaak Ti and the Barriss is the emitter. In fact if you buy the Shaak Ti the Barriss is already incuded you just remove the emitter section. However if you want to display both side by side i think its better not to pay for the parts you don't need. More info on the development please read this THREAD


To design this hilt I used multiple images from the propstore and exhibitions. here are the main references


Here are some screens of my models.

The key features besides the compatibility of sections with the other CSC sabers are the following:

1. Aluminum and Brass parts. Overall length 252mm
2. 2 button setup. The buttons are also the beveled LEDs
3. All knobs and beveled LEDs have the same threading meaning you can swap them if you want.
4. Can fit a 28mm speaker
5. Basic chassis design available for download
6. 2Switch + 2pixel PCB available for purchase (for ease of install). This is the same PCB that will be available for the Fisto hilts
7. 10 pixel PCB will be available for purchase for the LED bar graph (Identical to the 5layer 0f c1ones)
8. Box is included. Artwork by Christian Cruz as always.
9. Installation options will be added later. As per my previous projects this will be done by Giovanny from Aldani Customs
10. Weathering option will be available

At the moment I have quoted 100 units in total, 75 Shaaks and 25 Barrisses; this can change based on the demand. However 100 minimum will be made to keep the cost low. Everything that is left over will be sold as components for the DIY crew.

Costs

Shaak Ti (Empty) $255
Barriss (Empty) $240

Schedule

We will begin today with the interest list, then Pre-Orders will start first week of April May and will be open until production is complete. Metal prototypes will be available around the third week of April. Production launches in May

Interest list is now open. Thank you for your support as always.

 

[FLS89]

Interested in a Shaak Ti.

 

[teecrooz]

Interested in Shaka Ti, but as Adi Gallia’s TPM saber in the saber box.

 

[guabe]

Interested in Shaka Ti, but as Adi Gallia’s TPM saber in the saber box.

Oh I almost forgot, all hilts will come with 2 pommel end caps, a media blasted and a polished one.



Polished

Blasted

Assembly

 

[Foe Hammer]

Interested in Shaka Ti, but as Adi Gallia’s TPM saber in the saber box.

Same here.

 

[djedi]

interested in both

 

[Khufu01]

Interested in both please.

 

[guabe]

For those who are in to DIY here are just a couple of examples of what you can combine with parts from the Clan #1

Note that the pommel thread and the emitter thread is the same so you can reverse the body direction as well.

 

[14trharris]

Definitely interested in a Shaak Ti! Is there any possibility of getting a non-vented pommel? I know its not accurate to the actual prop, but it would make it a bit more accurate to the hilt seen in The Clone Wars.

 

[guabe]

Definitely interested in a Shaak Ti! Is there any possibility of getting a non-vented pommel? I know its not accurate to the actual prop, but it would make it a bit more accurate to the hilt seen in The Clone Wars.

let me ask the shop if they can do 1 or 2 without holes.

 

[14trharris]

let me ask the shop if they can do 1 or 2 without holes.

Thank you so much!! Is there anything special we need to do to order a Shaak Ti with an additional Barriss emitter or will the stand alone Barriss emitter become available in the store at some point after the pre-order closes?

 

[guabe]

Thank you so much!! Is there anything special we need to do to order a Shaak Ti with an additional Barriss emitter or will the stand alone Barriss emitter become available in the store at some point after the pre-order closes?

When you buy the Shaak Ti, the Barriss emitter is included already. You only remove the top parts and the botom piece of the emitter is also a blade holder for the barriss. In other words when you just buy the Barriss version, you will not get the steel radiator, the brass holder nor the top piece. The blade plug is the same for both.

 

[guabe]

Here are some nicer renders of the Shaak ti

And here are the quick renders of the Sw PCB and the bar graph pcb by Sam @ Shadowfoil



The cost of each pcb is $5 usd. The sw pcb is the exact same as the Fisto.

 

[CamWalker]

I'm definitely interested in the Shaak Ti!

 

[audiovideofreak]

Interested in both. Thank you.

 

[Razoresque]

Next on the CSC system is the Shaak Ti / Barriss Offee hilts. Being part of this system means that the threading is compatible with the first project LINK
View attachment 1799816
Main difference between the Shaak Ti and the Barriss is the emitter. In fact if you buy the Shaak Ti the Barriss is already incuded you just remove the emitter section. However if you want to display both side by side i think its better not to pay for the parts you don't need. More info on the development please read this THREAD

View attachment 1799817View attachment 1799818
To design this hilt I used multiple images from the propstore and exhibitions. here are the main references
View attachment 1799819View attachment 1799820View attachment 1799821View attachment 1799822View attachment 1799823

Here are some screens of my models.
View attachment 1799826View attachment 1799824View attachment 1799825View attachment 1799827View attachment 1799828View attachment 1799830View attachment 1799831
View attachment 1799829

The key features besides the compatibility of sections with the other CSC sabers are the following:

1. Aluminum and Brass parts. Overall length 252mm
2. 2 button setup. The buttons are also the beveled LEDs
3. All knobs and beveled LEDs have the same threading meaning you can swap them if you want.
4. Can fit a 28mm speaker
5. Basic chassis design available for download
6. 2Switch + 2pixel PCB available for purchase (for ease of install). This is the same PCB that will be available for the Fisto hilts
7. 10 pixel PCB will be available for purchase for the LED bar graph (Identical to the 5layer 0f c1ones)
8. Box is included. Artwork by Christian Cruz as always.
9. Installation options will be added later. As per my previous projects this will be done by Giovanny from Aldani Customs
10. Weathering option will be available

At the moment I have quoted 100 units in total, 75 Shaaks and 25 Barrisses; this can change based on the demand. However 100 minimum will be made to keep the cost low. Everything that is left over will be sold as components for the DIY crew.

Costs

Shaak Ti (Empty) $255
Barriss (Empty) $240

Schedule

We will begin today with the interest list, then Pre-Orders will start first week of April and will be open until production is complete. Metal prototypes will be available around the third week of April. Production launches in May

Interest list is now open. Thank you for your support as always

 

[ooRONINoo]

Interested in both.

 

[kamakazykid]

Ill take one of each

 

[JAC5]

Im interested in a Shaak-Ti, with both a vented and non-vented pommel please

 

[Shinki-Ro]

Interested in the Shaak Ti!